A Step-by-Step Overview to Setting Up a Bathtub
A Step-by-Step Overview to Setting Up a Bathtub
Blog Article
The article following next on the subject of Tools You Need to Install a New Bathtub is truly fascinating. Try it and draw your own personal conclusions.

Mounting a bathtub isn't specifically rocket science, yet it does require solid plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is easily obtainable, the project can relocate speedily; if you need to open a wall to remove the old tub and also position the brand-new tub, the job is much harder. In either instance, the job is within a residence handyman's abilities, although you will certainly require a helper to leave the old bathtub and embeded in the new one. Make certain you have actually qualified yourself for the work and fit trying it. Instead of hiring a specialist to take control of a halfway-completed task, it is better to take into consideration using one before you begin. Opportunities are you may need an expert plumber to make tube links.
This write-up will help you set up a brand-new bath tub in your bathroom if you have already gotten a brand-new tub and don't require to transform the plan of your previous water supply pipes.
Your tools as well as product checklist should comprise the following:
Planning for the Installment
Firstly, the supporting frame supplied with the bath ought to be fitted (if needed) according to the producer's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the versatile faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The process of removing the existing taps can be fairly bothersome as a result of the limited access that is typically the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a towel ready for the remaining water that will certainly originate from the pipelines. Once the supply pipes have actually been eliminated, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to proceeding to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the needed placement. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by checking the level and also changing the feet on the bath tub up until the level checks out level.
To set up taps, fit all-time low of the furthest flexible faucet port to the suitable supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water as well as examine all joints and brand-new pipework for leaks and also tighten them if essential. Fill the tub and also examine the overflow outlet and also the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as explained in the maker's user's manual. Tiling and securing around the bathtub should wait up until the bath tub has actually been used at the very least when as this will settle it right into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the tap in place with the producer supplied backnut. As soon as the faucet is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical tap ports. The previous kind needs to be connected to the tap ends first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall between the bath as well as the tiling, resulting in problems with wetness and also feasible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill the bathtub with water prior to securing, to enable the motion experienced when the tub remains in usage. The sealant can crack rather early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily readily available on the marketplace. It is advisable to fit the floor tiles using waterproof or water resistant adhesive and also grout.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
I ran across that article about Installing A Bathtub when scouting around the web. Sharing is caring. Helping others is fun. I am grateful for your time. Come back soon.
Book An Estimate Now
Report this page